PCB Prototype

Rapid PCB Prototype Service

Category: Circuit Board Assembly (page 2 of 23)

Vacuum Vapour SMT Soldering – Steel River Manufacturing



High reliability vacuum vapour soldering of double sided SMT PCB assemblies for virtual void free solder joints.

source

Four Suggestions for Picking a Small-quantity PCB Assembly Producer

pc board assy

Working with low-quantity PCB assemblies has its benefits and disadvantages. As the consumer, there are some tips that will allow you to obtain the most out of your assembly. Outlined in this article, we’re going to show you how to maximize the positive aspects and approaches to steer clear of the negative aspects.

The way to Pick a Small-quantity PCB Assembly Producer?

The ideas listed down the page can help you obtain the most out of your low-quantity PCB assembly order.


1. One Manufacturer

Opt for a low-quantity PCB manufacturer who can be a one-stop service provider for all of your PCB requirements. The luxury of working with a small order is you don’t have to coordinate with multiple organizations or individuals. Your order can be handled by a single point of contact.


2. Significance of Prototypes

Even though working with small orders, you must insist on use of prototypes – even if it causes an extra cost. Prototypes will assist you to check your design and improve on it, when necessary.


3. Small-quantity PCB Producer

pc board assy

Fabricating low-quantity PCB assemblies could be a task when collaborating with an rookie manufacturer. As the order quantity is low, cost of production will likely be a little higher. Consequently, any misstep by the PCB manufacturer will generate bigger losses for the purchaser.


4. Standard PCB Practices

Standard tips concerning PCB fabricating should be taken even when working with a low-quantity PCB assembly. This can include design, fabricating, assy, as well as PCBA testing steps.

Working with a low-quantity PCB assembly has its own range of positive factors. Utilising standard best practices will let you build an order that can help you in the end.

Manufacturing at Home — Sticky Watch #1



The first of a video series exploring the possibility of small batch manufacturing of my original electronic product at home.

I will cover:
・circuit design
・PCB design
・PCB assembly (reflow soldering w/ an oven)
・3D printing
・silicone casting w/ a 3D printed mold
・final assembly
・programming

The Sticky Watch is going to be on sale soon! I’ll update when that happens.

source

Four Strategies to Picking out a Low-quantity PCB Assembly Fabricator

pwb assembly

Working with small-quantity PCB assemblies has its upsides and downsides. As the customer, there are several tips that will assist you to get the most from your assembly. Outlined in this article, we’ll let you know how to benefit from the benefits and ways to get around the drawbacks.

Ways to Opt for a Low-quantity PCB Assembly Fabricator?

The ideas pointed out just below should help you make the most from your small-quantity PCB assembly order.


1. One Supplier

Find a small-quantity PCB maker who could be a one-stop provider for all of your PCB needs. The benefit of working with a small order is that you don’t have to coordinate with a couple of organizations or individuals. Your order can be handled by a single point of contact.


2. Worth of Prototypes

Although working with small orders, you must insist upon use of prototypes – though it comes at an extra expense. Prototypes will help you to check your design and refine it, if needed.


3. Low-quantity PCB Fabricator

pwb assembly

Making small-quantity PCB assemblies can be quite a task when using an unsophisticated maker. As the order quantity is low, expense of production will be moderately higher. For that reason, any error by the PCB maker will result in larger losses for the consumer.


4. Standard PCB Practices

Standard tips relating to PCB production should be obeyed despite the fact that working with a small-quantity PCB assembly. This consists of design, fabrication, assembly, and PCBA testing procedures.

Working with a small-quantity PCB assembly has its own couple of rewards. Taking advantage of standard suggestions will let you build an order that might help you down the road.

Why through-hole technology is not dead yet



Why do we still use through-hole technology to make PCB assemblies, when SMT boards are typically smaller and cheaper?

source

4 Rules to Choosing a Small-quantity PCB Assembly Producer

pwb assemblies

Working with low-volume PCB assemblies has its advantages and cons. As the client, there are several hints that can help you get the most from your assembly. In this posting, we’ll let you know how to maximize the benefits and ways to move around the negatives.

Methods to Pick a Small-quantity PCB Assembly Producer?

These tips referred to below can help you make the most from your low-volume PCB assembly order.


1. One Service Provider

Pick out a low-volume PCB maker who can be a one-stop service provider for all of your PCB requires. The main advantage of working with a small order is that you don’t need to coordinate with a couple of organizations or individuals. Your order can be handled by a single point of contact.


2. Need for Prototypes

Even if working with small orders, you must require use of prototypes – even though it results in an further expense. Prototypes will permit you to inspect your design and fix it, if necessary.


3. Small-quantity PCB Producer

pwb assemblies

Producing low-volume PCB assemblies can be quite a task when employing an inexperienced maker. For the reason that order quantity is low, cost of production is going to be gently higher. Therefore, any error on the part of the PCB maker will bring about greater losses for the customer.


4. Standard PCB Practices

Standard guidelines relating to PCB production really should be adopted despite the fact that working with a low-volume PCB assembly. This can include design, fabricating, assy, and in addition PCBA testing processes.

Working with a low-volume PCB assembly has its own group of positive aspects. Making use of standard guidelines will allow you to build an order that can help you over time.

PCB Visual Check – Pre shipment Inspection (www.advantage.co.th)



Advantage co.,Ltd
Quality in quality control
and inspcection

source

Four Tricks to Picking out a Small-quantity PCB Assembly Producer

pcb assemblies

Working with small-quantity PCB assemblies has its advantages and disadvantages. As the buyer, there are several suggestions that will let you obtain the most out of your assembly. Below, we shall let you know how to make use of the advantages and ways to avoid the negative aspects.

The right way to Opt for a Small-quantity PCB Assembly Producer?

The ideas mentioned here should help you make the most out of your small-quantity PCB assembly order.


1. Single Provider

Select a small-quantity PCB maker who could be a one-stop supplier for all of your PCB requirements. The advantage of working with a small order is basically that you don’t need to coordinate with a couple of organizations or individuals. Your order can be handled by a single point of contact.


2. Value of Prototypes

Even though working with small orders, you must insist upon using prototypes – despite the fact that it leads to an added cost. Prototypes will permit you to review your design and improve on it, as required.


3. Small-quantity PCB Producer

pcb assemblies

Making small-quantity PCB assemblies can be a task when using an unskilled maker. Given that the order quantity is low, cost of production will probably be a bit higher. Therefore, any misstep from the PCB maker will produce greater losses for the consumer.


4. Standard PCB Practices

Standard best practices related to PCB making really should be taken even when working with a small-quantity PCB assembly. This can include design, manufacturing, assy, and PCBA testing procedures.

Working with a small-quantity PCB assembly has its own variety of gains. Utilising standard best practices will allow you to build an order that may help you over time.

Electronics Manufacturing – Ducommun LaBarge



Ducommun LaBarge Technologies is another preferred American supplier of contract manufacturing services you will find only at a Design-2-Part trade show at http://www.d2p.com.

Ducommun LaBarge Technologies specializes in solutions — smart, innovative and reliable answers to their customers’ needs.

Their full-service approach combines broad-based manufacturing capabilities and extensive value-added services, including professional engineering support and program management, to help our customers achieve their goals.They draw upon best-in-class processes, our continuous improvement culture and a passionate commitment to excellence to deliver quality in everything they do.

Their niche in the broad Electronics Manufacturing Services (EMS) industry is low-to-medium volume production of highly complex, high-rate-of-change electronic and electromechanical products and systems. Their full-service EMS capabilities include cable assemblies and interconnect systems, printed circuit board assemblies, higher-level electronic and electromechanical assemblies, and system integration, along with engineering and design support, and program management.

source

4 Rules to Finding a Small-run PCB Assembly Manufacturer

pwb assembly

Working with low-quantity PCB assemblies has its advantages and drawbacks. As the consumer, there are several points that will let you make the most from your assembly. In the following paragraphs, we’re going to show you how to make use of the positives and the ways to stay away from the downsides.

Tips to Select a Small-run PCB Assembly Manufacturer?

The ideas listed in this article should help you obtain the most out of your low-quantity PCB assembly order.


1. A Single Supplier

Pick out a low-quantity PCB fabricator who can be a one-stop service provider for all your PCB needs. The good thing about working with a small order is basically that you don’t have to coordinate with several organizations or individuals. Your order can be handled by a single point of contact.


2. Significance of Prototypes

Even when working with small orders, you must insist upon using prototypes – despite the fact that it causes an further expense. Prototypes will enable you to review your design and make improvements to it, if necessary.


3. Small-run PCB Manufacturer

pwb assembly

Making low-quantity PCB assemblies can be a task when employing an rookie fabricator. Since the order quantity is low, expense of production will be moderately higher. As a consequence, any error on the part of the PCB fabricator will be a catalyst for bigger losses for the buyer.


4. Standard PCB Practices

Standard best practices associated with PCB fabricating must be obeyed regardless if working with a low-quantity PCB assembly. This can include design, fabrication, assembly, and also PCBA testing steps.

Working with a low-quantity PCB assembly has its own variety of perks. With the help of standard best practices will assist you to build an order that may help you in time.

SOLIDWORKS PCB Solutions



SOLIDWORKS has two solutions for the electronic design industry: SOLIDWORKS PCB Connector for Altium users and SOLIDWORKS PCB a standalone PCB solution. Both solutions bring real-time integration to E-CAD and M-CAD collaboration.

source

Four Rules to Deciding on a Small-run PCB Assembly Fabricator

pcb assy

Working with small-run PCB assemblies has its upsides and disadvantages. As the client, there are several suggestions that can help you make the most from your assembly. Here, we’ll explain how to maximize the pluses and approaches to move around the shortcomings.

The right way to Go with a Small-run PCB Assembly Fabricator?

The guidelines mentioned just below should help you obtain the most out of your small-run PCB assembly order.


1. Single Provider

Find a small-run PCB maker who could be a one-stop provider for all of your PCB needs. The good thing about working with a small order is you don’t have to coordinate with a couple of organizations or individuals. Your order can be treated by a single point of contact.


2. Significance of Prototypes

Even if working with small orders, you must require use of prototypes – although it comes at an extra expenditure. Prototypes will assist you to review your design and improve on it, when necessary.


3. Small-run PCB Fabricator

pcb assy

Producing small-run PCB assemblies can be quite a task when collaborating with an not experienced maker. Since the order quantity is low, cost of production will be somewhat higher. Consequently, any misstep by the PCB maker will give rise to increased losses for the purchaser.


4. Standard PCB Practices

Standard best practices concerning PCB making ought to be followed even when working with a small-run PCB assembly. This consists of design, manufacturing, assy, and in addition PCBA testing procedures.

Working with a small-run PCB assembly has its own range of pluses. With standard recommendations will allow you to build an order that can help you in the long term.

Ceramic PCB Substrate Manufacturer Metallization Service



CLICK HERE: http://www.tensky.com.tw/page/html/en.php

We are a professional manufacturer and supplier of the following:

Ceramic PCB Manufacturer
Ceramic Substrate Manufacturer
Ceramic Metallization Service
Ceramic DPC Manufacturer
Thin Film Ceramic Substrates
Electronic Ceramic Supplier
Fine Ceramic Parts
Semiconductor Ceramics Parts
Advance Ceramic Parts
Precision Machined Ceramics
AL2O3 Ceramic Supplier
ZRO2 Ceramic Supplier
SI3N4 Ceramic Manufacturer
CNC Metal Parts Manufacturer
Industrial Ceramics Manufacturer
High Temperature Ceramic Coating
Anti ESD Coating
Anti Glue Coating
Silicon Carbide Coating Services
Anti Plasma Coating

Visit our site for complete product information and

Tensky International (Technology) Co., Ltd. mainly supply all kinds of electronic products and precision ceramic products, ceramic and fine porcelain, TSK adhere to build an international brand for the business goals and ideals, and in 2009 put into ceramic circuit board (substrate) of the R & D and production and a high-tech enterprises.

After years of rapid development, starting from the development of fine ceramics, cross-sell fine ceramics to the world, then in 2009, successfully entered the high power and high heat ceramic circuit board (substrate), and now TSK in mainland China in Shenzhen, Dongguan, Guangzhou, Foshan, Japan, South Korea, Russia, the United States and Germany Jieyou cooperation LED packaging manufacturers and suppliers to the needs of ceramic substrate factory, the products are widely used in high power LED ceramic substrate, microwave wireless communications, HCPV solar animal cells, ceramic sensor substrates, semiconductor and military electronics.

source

Four Suggestions to Selecting a Small-run PCB Assembly Producer

pcb board assy

Working with small-volume PCB assemblies has its advantages and drawbacks. As the consumer, there are a few strategies that will let you get the most out of your assembly. In this article, we’ll let you know how to make use of the benefits and approaches to move around the negative aspects.

Easy methods to Pick a Small-run PCB Assembly Producer?

The ideas pointed out here should help you make the most out of your small-volume PCB assembly order.


1. One Provider

Choose a small-volume PCB manufacturer who could be a one-stop provider for all your PCB demands. The main benefit of working with a small order is that you don’t need to coordinate with several organizations or individuals. Your order can be handled by a single point of contact.


2. Significance of Prototypes

Even when working with small orders, you must insist upon use of prototypes – though it comes at an further cost. Prototypes will allow you to check your design and make improvements to it, when needed.


3. Small-run PCB Producer

pcb board assy

Producing small-volume PCB assemblies can be quite a task when employing an unskilled manufacturer. Because the order quantity is low, expense of production will be to some extent higher. Therefore, any error on the part of the PCB manufacturer will result in greater losses for the client.


4. Standard PCB Practices

Standard tips relating to PCB fabrication really should be taken although working with a small-volume PCB assembly. This includes design, fabrication, assemblage, as well as PCBA testing processes.

Working with a small-volume PCB assembly has its own variety of perks. Utilising standard suggestions enables you to build an order that might help you in time.

PCB functional test



Functional test (FCT) is used as a final manufacturing step. It provides a pass/fail determination on finished PCBs before they are shipped. For more information, please visit http://www.7pcbmanufacturing.com

source

4 Tips to Deciding on a Low-volume PCB Assembly Manufacturer

pcb board assembly

Working with small-run PCB assemblies has its advantages and drawbacks. As the client, there are a few pointers that will help you obtain the most out of your assembly. In the following paragraphs, we’re going to let you know how to capitalize on the pros and the ways to keep away from the drawbacks.

Find out how to Pick a Low-volume PCB Assembly Manufacturer?

The guidelines referred to down the page should help you get the most out of your small-run PCB assembly order.


1. Single Manufacturer

Select a small-run PCB producer who could be a one-stop supplier for all your PCB demands. The main advantage of working with a small order is you don’t have to coordinate with a couple of organizations or individuals. Your order can be treated by a single point of contact.


2. Significance of Prototypes

Although working with small orders, you must require using prototypes – although it comes at an further expense. Prototypes will allow you to look into your design and refine it, as you desire.


3. Low-volume PCB Manufacturer

pcb board assembly

Producing small-run PCB assemblies can be a task when hiring an rookie producer. For the reason that order quantity is low, expense of production is going to be to some degree higher. Thereby, any misstep from the PCB producer will produce increased losses for the purchaser.


4. Standard PCB Practices

Standard guidelines involving PCB making ought to be obeyed regardless if working with a small-run PCB assembly. This can include design, fabrication, assembly, as well as PCBA testing processes.

Working with a small-run PCB assembly has its own variety of positive aspects. By making use of standard tips allows you to build an order that might help you eventually.

IPC-A-610F Video Training for TH & SM Solder Joint Quality Standards



A partial demo of IPC training videos on IPC-A-610F — the industry standard for “Acceptability of Electronic Assemblies” — covering solder joint quality requirements for through hole and surface mount components. (IPC part numbers: DVD-PTH-F and DVD-SMT-F)

For free, full-length reviews of all IPC media training certification programs, please visit our electronics assembly training website at: http://www.ipctraining.org

source

4 Rules to Deciding on a Small-run PCB Assembly Maker

printed circuit board assemblies

Working with low-quantity PCB assemblies has its upsides and downsides. As the purchaser, there are several helpful tips that will assist you to obtain the most out of your assembly. Here, we will let you know how to take advantage of the positive aspects and the ways to keep away from the disadvantages.

Simple methods to Pick a Small-run PCB Assembly Maker?

The tips listed in this article will help you make the most out of your low-quantity PCB assembly order.


1. Just One Supplier

Choose a low-quantity PCB manufacturer who can be a one-stop provider for all of your PCB needs. The benefit of working with a small order is you don’t need to coordinate with multiple organizations or individuals. Your order can be handled by a single point of contact.


2. Incredible importance of Prototypes

Even if working with small orders, you must insist on using prototypes – despite that it comes at an increased cost. Prototypes will help you to inspect your design and make improvements to it, as you desire.


3. Small-run PCB Maker

printed circuit board assemblies

Making low-quantity PCB assemblies can be quite a task when hiring an inexperienced manufacturer. Given that the order quantity is low, cost of production will probably be slightly higher. For this reason, any mistake by the PCB manufacturer will induce greater losses for the consumer.


4. Standard PCB Practices

Standard suggestions involving PCB fabrication should be taken even if working with a low-quantity PCB assembly. This consists of design, fabricating, assy, and additionally PCBA testing processes.

Working with a low-quantity PCB assembly has its own group of plus points. Using standard tips will permit you to build an order that will help you ultimately.

ViTrox_Advanced 3D Optical Inspection system (AOI)



Advanced 3D Optical Inspection system (AOI) is designed to specially cater to different sizes of PCB assembly to be examined at the micron level with maximum throughput. This translates to increased production efficiency and cost savings for manufacturers.

source

4 Rules to Finding a Small-run PCB Assembly Manufacturer

printed circuit board assy

Working with low-quantity PCB assemblies has its benefits and downsides. As the client, there are several pointers that will let you make the most from your assembly. In the following paragraphs, we’re going to explain how to capitalize on the pros and ways to move around the negative aspects.

How you can Pick out a Small-run PCB Assembly Manufacturer?

The guidelines brought up in this article will help you make the most out of your low-quantity PCB assembly order.


1. Only One Supplier

Decide on a low-quantity PCB producer who could be a one-stop supplier for all your PCB requires. The great thing about working with a small order is basically that you don’t need to coordinate with various organizations or individuals. Your order can be handled by a single point of contact.


2. Incredible importance of Prototypes

Even though working with small orders, you must require using prototypes – even in the event it comes at an added expense. Prototypes allows you to evaluate your design and improve on it, if needed.


3. Small-run PCB Manufacturer

printed circuit board assy

Making low-quantity PCB assemblies could be a task when working together with an unskilled producer. Because the order quantity is low, cost of production will be to some extent higher. Subsequently, any mistake on the part of the PCB producer will contribute to larger losses for the purchaser.


4. Standard PCB Practices

Standard suggestions relating to PCB fabrication ought to be followed although working with a low-quantity PCB assembly. This can include design, manufacturing, assy, as well as PCBA testing processes.

Working with a low-quantity PCB assembly has its own set of pros. Utilizing standard recommendations will allow you to build an order that will help you over time.

Older posts Newer posts

© 2018 PCB Prototype

Up ↑