PCB Prototype

Rapid PCB Prototype Service

Month: July 2017 (page 1 of 5)

PCB Functional Testing



www.melitech-design.com

This is an example of a PCB automated programming and functional test equipment. It was developed and assembled by Melitech Design Ltd for a client. This system can test 7 different pcbs just by changing the cassette with bed of nails. The rest is common for all boards. The system was built using the following components which are available from our stock.:

PCB Test Adaptor
Cassette for Bed of nails
Controller Card
Relay expansion board
LCD Module

These can be bought as components to build your own system or we can design, machine and build the system for you according to your pcb testing requirements.

Feel free to contact us for further information on

info@melitech-design.com

or visit our website

www.melitech-design.com

source

Four Suggestions for Choosing a Low-volume PCB Assembly Producer

pwb assembly

Working with small-quantity PCB assemblies has its benefits and drawbacks. As the buyer, there are several pointers that will let you get the most out of your assembly. In this posting, we’re going to let you know how to utilize the benefits and the ways to get around the problems.

Methods to Pick out a Low-volume PCB Assembly Producer?

The information referred to just below should help you make the most from your small-quantity PCB assembly order.


1. One Supplier

Decide on a small-quantity PCB fabricator who can be a one-stop provider for all your PCB needs. The main benefit of working with a small order is basically that you don’t need to coordinate with a couple of organizations or individuals. Your order can be handled by a single point of contact.


2. Incredible importance of Prototypes

Even if working with small orders, you must insist upon use of prototypes – regardless if it brings about an additional expense. Prototypes will permit you to inspect your design and improve on it, when required.


3. Low-volume PCB Producer

pwb assembly

Manufacturing small-quantity PCB assemblies can be a task when working with an unsophisticated fabricator. Since the order quantity is low, expense of production will be a little higher. So, any mistake from the PCB fabricator will be responsible for larger losses for the consumer.


4. Standard PCB Practices

Standard suggestions involving PCB producing needs to be followed even when working with a small-quantity PCB assembly. This consists of design, manufacturing, assemblage, and even PCBA testing procedures.

Working with a small-quantity PCB assembly has its own variety of positive factors. With the help of standard best practices will help you to build an order that might help you over the long haul.

EC Electronics Ltd – Electronic Assembly and Cable Assembly



EC Electronics provide ISO 9001:2008 approved Contract Electronic Manufacturing Services (CEMS) including PCB Assembly, Cable Assembly and Final Product Assembly to IPC standards from factories located in the UK and Romania.

source

4 Strategies to Picking out a Low-quantity PCB Assembly Manufacturer

pwb assembly

Working with low-quantity PCB assemblies has its advantages and drawbacks. As the consumer, there are a few strategies that can help you obtain the most out of your assembly. In this posting, we’ll let you know how to maximize the good things and the ways to keep clear of the downsides.

Methods to Go with a Low-quantity PCB Assembly Manufacturer?

The guidelines brought up just below should help you maximum benefit from your low-quantity PCB assembly order.


1. Single Supplier

Opt for a low-quantity PCB fabricator who could be a one-stop service provider for all of your PCB needs. The main advantage of working with a small order is you don’t have to coordinate with various organizations or individuals. Your order can be treated by a single point of contact.


2. Incredible importance of Prototypes

Even when working with small orders, you must insist on using prototypes – though it results in an extra cost. Prototypes allows you to evaluate your design and improve on it, at will.


3. Low-quantity PCB Manufacturer

pwb assembly

Fabricating low-quantity PCB assemblies can be a task when using an unsophisticated fabricator. Considering that the order quantity is low, expense of production is going to be a bit higher. For this reason, any error by the PCB fabricator will mean increased losses for the consumer.


4. Standard PCB Practices

Standard suggestions concerning PCB producing ought to be used even though working with a low-quantity PCB assembly. This consists of design, fabricating, assemblage, and even PCBA testing steps.

Working with a low-quantity PCB assembly has its own variety of merits. With the help of standard tips will assist you to build an order that can help you eventually.

Perfect PCB Assembly



Specifications:
PCB:
Base material: FR4
Layer count: four
Board thickness: 1.6mm
Copper thickness: 1oz
Surface finish: HASL
Soldermask color: green
Dimensions: 130.4 x 149.46/2up

SMT:
Capacitance: 42 pieces
Electric resistance: (0603) 45 pieces
LED lamp: six pieces
Video and interface unit: 20 pieces
Diode and triode: 30 pieces
IC: 20 pieces

Primary competitive advantages:

High-precision machine and equipment can guarantee quality X-ray, AOI, visual checking and function test confirm our delivery goods 100% past
No MOQ
Competitive price and short lead-time
Rich experience in importing and exporting

source

Four Tricks to Picking out a Small-quantity PCB Assembly Maker

pcb board assy

Working with small-run PCB assemblies has its advantages and cons. As the consumer, there are some strategies that can help you maximum benefit from your assembly. Outlined in this article, we are going to show you how to capitalize on the plus points and approaches to bypass the negatives.

The way to Choose a Small-quantity PCB Assembly Maker?

The ideas talked about below will help you obtain the most from your small-run PCB assembly order.


1. One Supplier

Choose a small-run PCB manufacturer who could be a one-stop service provider for all your PCB demands. The advantage of working with a small order is basically you don’t need to coordinate with various organizations or individuals. Your order can be handled by a single point of contact.


2. Significance of Prototypes

Although working with small orders, you must require use of prototypes – even if it comes at an added expenditure. Prototypes will enable you to inspect your design and improve on it, when required.


3. Small-quantity PCB Maker

pcb board assy

Manufacturing small-run PCB assemblies can be quite a task when using an low compertition manufacturer. Since the order quantity is low, cost of production is going to be a little bit higher. Thereby, any mistake from the PCB manufacturer will result in bigger losses for the buyer.


4. Standard PCB Practices

Standard guidelines associated with PCB fabrication really should be obeyed even when working with a small-run PCB assembly. This can include design, fabricating, assy, and also PCBA testing procedures.

Working with a small-run PCB assembly has its own set of positive factors. Taking advantage of standard tips allows you to build an order that will help you at the end.

Auto Insertion for PCB assembly



This is an auto insertion machine for PCB assembly from Sciencgo in China, very efficient and reliable but low cost. please contact me at : jasonwu@sciencgo.com or w25605@gmail.com if you are interested. We design and manufacture SMT equipment in Shenzhen China;

1, LED SMT solutions : one full line (1.2m printer + 20k CPH LED mounter + 6 zone oven) price lower at usd 50K.
http://www.smthelp.com/product/led-smt-machine/

2, Odd form insertion machine:
http://www.smthelp.com/product/s-7000i-odd-form-inserter/

3, Pneumatic stencil cleaner: —No need electronic power, no fire and detonate caused; Simple operation, only Start, Stop and Reset, that is all;, Protecting Environmental, water recycle ;Lower consumption .
http://www.smthelp.com/product/stencil-cleaner-machine/

4, Spare parts support.
See why we are proud to be Southern Machinery .
http://www.smthelp.com/product/pcb-design-guideline/
1, LED Mounter
https://www.youtube.com/channel/UC4Z_P3S6qAYLHnlE-DU2OSA
2, Through hole technilogy
https://www.youtube.com/channel/UC6Pj74wjjEjtp-jneRoSL9Q
3,SMT Machine For PCB Assembly
https://www.youtube.com/channel/UCke0s_OM0eKflD8WmGSLm5A
4,Odd Form Insertion Machine/Feeder
https://www.youtube.com/channel/UCactVXP8IrU3l-vItOODRCA
5,AI SMT spare parts
https://www.youtube.com/channel/UCMuFHjsSuaIXnc3_3yNcwzw
6, Stencil Cleaner Machine Southern Machinery
https://www.youtube.com/channel/UCnMRyXlBFqJZHYuqaZVoK4Q
7,SMT pcb assembly LED
https://www.youtube.com/channel/UClX0iEG2bvJq8yUBEDamgDw

-~-~~-~~~-~~-~-
Please watch: “How to operate Auto Insertion Machine to Assembly PCB by Through hole technology”

Email: info@smthelp.com
-~-~~-~~~-~~-~-

source

Four Ideas to Picking out a Low-quantity PCB Assembly Maker

pwb assemblies

Working with low-volume PCB assemblies has its advantages and disadvantages. As the customer, there are several points that will allow you to obtain the most from your assembly. Here, we shall let you know how to capitalize on the possible benefits and the ways to keep clear of the negatives.

The best way to Choose a Low-quantity PCB Assembly Maker?

These tips brought up here should help you maximum benefit out of your low-volume PCB assembly order.


1. Only One Manufacturer

Pick a low-volume PCB producer who can be a one-stop service provider for all of your PCB requirements. The best thing about working with a small order is basically you don’t need to coordinate with various organizations or individuals. Your order can be treated by a single point of contact.


2. Need for Prototypes

Even though working with small orders, you must insist on using prototypes – although it comes at an additional cost. Prototypes will help you to evaluate your design and improve on it, if required.


3. Low-quantity PCB Maker

pwb assemblies

Making low-volume PCB assemblies can be quite a task when hiring an low compertition producer. Because the order quantity is low, expense of production will probably be a bit higher. Hence, any mistake by the PCB producer will induce higher losses for the purchaser.


4. Standard PCB Practices

Standard best practices concerning PCB production should be implemented despite the fact that working with a low-volume PCB assembly. This can include design, fabrication, assembly, as well as PCBA testing processes.

Working with a low-volume PCB assembly has its own couple of pros. Employing standard suggestions will enable you to build an order that will help you eventually.

Electronic Assembly by Easy EMS India, Noida



[http://www.easyemsindia.com/] Welcome to Easy EMS India, established in the year 2014, we are one of the leading manufacturers, exporter and suppliers of a wide range of the premium quality of Electronic Assembly. The product range offered by us inclusive of SMT PCB Assembly, LED PCB Assembly Board and Prototype PCB Assembly. Owing to their superior functionality, compact design, sturdy construction and easy installation, these printed circuit boards are highly demanded in the market. In addition to this, we offer the high quality Electronic Manufacturing Services and PCB Assembly Services to our esteemed customers. Their timely execution and premium effectiveness, makes these manufacturing services highly appreciated among our customers.

source

4 Strategies to Choosing a Low-volume PCB Assembly Manufacturer

pwb assemblies

Working with small-volume PCB assemblies has its upsides and cons. As the purchaser, there are a few suggestions that will assist you to make the most from your assembly. In this article, we’ll show you how to take advantage of the pros and the ways to bypass the negatives.

How one can Pick a Low-volume PCB Assembly Manufacturer?

The guidelines talked about here should help you maximum benefit from your small-volume PCB assembly order.


1. A Single Provider

Decide on a small-volume PCB maker who can be a one-stop provider for all your PCB demands. The advantage of working with a small order is basically you don’t need to coordinate with several organizations or individuals. Your order can be handled by a single point of contact.


2. Need for Prototypes

Even though working with small orders, you must require using prototypes – even in the event it comes at an extra expenditure. Prototypes will enable you to look into your design and fix it, as you desire.


3. Low-volume PCB Manufacturer

pwb assemblies

Making small-volume PCB assemblies can be quite a task when working with an rookie maker. For the reason that order quantity is low, expense of production will likely be moderately higher. Therefore, any error from the PCB maker will induce larger losses for the consumer.


4. Standard PCB Practices

Standard suggestions related to PCB fabricating ought to be obeyed despite the fact that working with a small-volume PCB assembly. This consists of design, manufacturing, assemblage, and even PCBA testing processes.

Working with a small-volume PCB assembly has its own set of pluses. Employing standard tips will permit you to build an order that may help you in the end.

PCB PIXture



PCB PIXture is a new tool for PCB designers who want to increase the visual impact of their boards. Typical applications include front panels, keyboards, PCB assemblies sold as independent units, consumer electronics … – anywhere where the distinctive appearance of your PCB will make an important selling point.

source

Four Tricks to Picking out a Small-run PCB Assembly Manufacturer

pc board assembly

Working with small-volume PCB assemblies has its upsides and disadvantages. As the consumer, there are several helpful tips that will assist you to obtain the most out of your assembly. In the following paragraphs, we’re going to show you how to benefit from the benefits and the ways to stay away from the negative aspects.

Tips on how to Pick a Small-run PCB Assembly Manufacturer?

The guidelines listed below will help you get the most from your small-volume PCB assembly order.


1. Single Provider

Go with a small-volume PCB maker who can be a one-stop provider for all of your PCB demands. The benefit of working with a small order is basically that you don’t need to coordinate with various organizations or individuals. Your order can be handled by a single point of contact.


2. Need for Prototypes

Even though working with small orders, you must insist upon using prototypes – though it results in an added cost. Prototypes enables you to evaluate your design and fix it, at will.


3. Small-run PCB Manufacturer

pc board assembly

Fabricating small-volume PCB assemblies could be a task when cooperating with an unsophisticated maker. Because the order quantity is low, expense of production will be to some extent higher. For this reason, any error from the PCB maker will bring about larger losses for the buyer.


4. Standard PCB Practices

Standard recommendations about PCB production ought to be obeyed despite the fact that working with a small-volume PCB assembly. This includes design, manufacturing, assemblage, and in addition PCBA testing procedures.

Working with a small-volume PCB assembly has its own group of positive factors. Utilizing standard suggestions will let you build an order that will help you over time.

Electronic PCB Assembly with water proof coating



ALBATRON’s conformal coat will protect an active, working circuit board as it is submerged water.

source

Four Tactics to Deciding on a Low-volume PCB Assembly Producer

pcb board assembly

Working with small-run PCB assemblies has its benefits and downsides. As the client, there are a few suggestions that can help you get the most out of your assembly. In the following paragraphs, we shall let you know how to make the most of the good things and the ways to keep away from the negative aspects.

Find out how to Go with a Low-volume PCB Assembly Producer?

The ideas talked about in this article should help you maximum benefit from your small-run PCB assembly order.


1. One Supplier

Pick out a small-run PCB maker who could be a one-stop service provider for all your PCB demands. The advantage of working with a small order is basically that you don’t need to coordinate with various organizations or individuals. Your order can be handled by a single point of contact.


2. Great need of Prototypes

Even if working with small orders, you must require use of prototypes – despite that it comes at an added cost. Prototypes will let you check your design and enhance it, if necessary.


3. Low-volume PCB Producer

pcb board assembly

Fabricating small-run PCB assemblies can be a task when employing an not experienced maker. Since the order quantity is low, expense of production is going to be marginally higher. For this reason, any mistake on the part of the PCB maker will cause increased losses for the customer.


4. Standard PCB Practices

Standard tips relating to PCB producing must be followed even if working with a small-run PCB assembly. This includes design, manufacturing, assembly, and even PCBA testing processes.

Working with a small-run PCB assembly has its own group of plus points. Utilizing standard guidelines will help you to build an order that might help you down the road.

CEM-3 PCB Board Facility Based in China Mainland



http://my.brainshark.com/Global-And-China-Printed-Circuit-Board-PCB-Industry-2014-Market-Research-Report-677334318 – QY Research Reports included a detailed market survey and trends analysis on Global And China Printed Circuit Board Industry 2014. This report also includes more info about basic overview of the industry including definitions, applications and industry china structure. For more info visit @ http://www.qyresearchreports.com/report/global-and-china-printed-circuit-board-pcb-industry-2014-deep-research-report.htm

Source

CEM-3 PCB Board Facility Based in China Mainland

2-pcb-house-factory

PCBWING Technology Co., Ltd (chiefly for prototype)

In line with https://www.pcbwing.com/Aboutus.php

PCBWING Technology Co., Ltd is among the list of China’s top rated company delivering electronic circuit board services, that is a collaboration of three of the top ten electronic circuit board makers in China. Our merits are fast-turn, small quantity orders.
We’re an innovative electronics contract manufacturer in Peking, China. We are already focused on electronic circuit board prototype in the past 12 years. We’ve served famous companies or associations in the world, for instance Microsoft, Hewlett packard, Toshiba, Jet Propulsion Laboratory of China, Altium, University of Cambridge, University of Wisconsin, Stanford University, Harvard University, Peking University, Siemens as well as China Mobile. We have competitive prices, well-trained specialists and superior production skills. We encouraged people to reach us and think about us as a efficient provider for electronic circuit board fabricating services.

We provide:
Quality. Competitive pricing. On-time shipping.

PCBWING Technology Co., Ltd will be your recommendable manufacturer for electronic circuit board prototype service.

Contact PCBWING

Sales Office Contact:
Sales@pcbwing.com

Support Contact:
Support@pcbwing.com

Advertising and marketing Contact: linli@pcbwing.com

Telephone:
+8615601330384

Address:
Room520A , Heqiao Plaza B Tower No.8 Guanghua Road
Chaoyang District , Beijing
China Postcode 100026

2-pcb-house-factory

STG

Based upon : http://www.china-pcbassembly.com/factory-view-n100-1.html

Turk-key PCB Board assemblage solution company

(Serving white-label PCB Board )

STG is a top proficient PCB Board and PCBA manufacturer in China, which provides OEM/ODM service for global consumers . With years of experiences, STG is not only a producer, but even a proficient designer for emerging concepts, new innovations dependant upon clients. Our product range covers many various fields, such as consumer electronics, telecoms, industrial items , car assemblies, medical equipment and so on.

Our major services consist of electronics and metal casing fabrication, for instance , printed circuit boards PCB Board manufacture, part procurement, PCB Board assemblage, plastic/metal house build, die-casting as well as custom manufacture. With skilled staff from STG well-trained, their performance will be outstanding.

Contact STG

China Shenzhen Office

TEL: +86-0755-27929725
Telefax: +86-0755-27929724
Email: sales@stgpcba.com

Address: Huolibao Building 5F , Technology Park, Nanshan, Shenzhen, 518100, China.
Web-site: www.china-pcbassembly.com

Hong Kong Office

Tel: 852-36458129
Fax: 852-36458092
Email: marketing@stgpcba.com.
Address: 11/F FRONT BLK,HANG LOK BLDG 130 WING LOK ST,SHEUNG WAN, Hong Kong
Web-site: www.china-pcbassembly.com .

2-pcb-house-factory

Topscom Technology Co.,Ltd.

As per : http://www.topscom.com.cn/info-132-en.html

Company Introduction

Twenty Years Of Electronics Turn-key OEM / ODM, Electronic Contract Manufacturing(otherwise known as ECM) and Circuit Board Assembling Services — China Topscom

Topscom is a top Electronics Manufacturing Services (sometimes known as EMS) supplier focused on providing cutting edge design and manufacturing services to auto, commercial, medical related, prospects, telephone system, and modern technology companies. With fiscal year 2013 profits of 360 , 000, 000 USD, Topscom aids prospects design, fabricate, shipping, and electronics which supplies clients with overall design, engineering, and fabricating resources which are vertically integrated with elements to optimize their operations by minimizing their charges and cutting down the time period to markets.

Topscom can provide an wide range of fabricating, engineering and machining services, for instance in-house highly precise SMT mount, plastic injection casting, high volume metal stamping, die-casting and tailor-made manufacture.

Full-equipped Sectors

Our different sections are aimed to provide an extensive range of manufacture, engineering and machining services:
Our SMT capacities address 0201, zero-Lead and flip-chip technologies.
Our plastic injection molding team is aligned with advanced devices in white room and cold water air conditioning system. A extraordinary production line is also created to take away and slice the material grain.
Our metal stamping section comes with CNC process center, silk devices and also drilling devices produced by Japan and Taiwan.
In our mold tooling division, we employ Pro-Engineer pro software program for effective design help. Utilizing EROWA grips, we can easily limit the accuracy within 3 ums.
To keep qc system efficacious, we routinely compare and contrast our test flow charts. Additionally we preserve purchasing offices in Tokyo, Singapore as well as Hong Kong manipulated by our centralized supplies warehouse in Shenzhen.

Our plant is based in Shenzhen, China with a sum place of 200,Thousand square meters and more than 4 thousand laborers. We extremely trust in the value of our workers and prefer to maintain a qualified attitude and corporate way of life that helps bring about creativity and boasts job happiness.

The managing emphasizes continual training, open communication, teamwork and contribution in decision-making process.

With enormous experience with cooperating with high-technology corporations and diverse client base in wide product selection, we’re very assured to offer great services, high adaptability, less expensive fabricating solutions and punctual delivery for our consumers.

Our first rate consumers list across the globe: Rda (Sydney) , Bestdl (Belgium), Sqp (France), Destst, Metro (Israel), Aji, Fujitsu, Sony (Japan), Dgsb (Malaysia), Rdi (Holland), Mlcroalp(Singapore), Inventron, Tempel (Spain), Imc (UK), Cisco (United States of America).

Find US

Telephone: +86-755-22211988 (50 Line)
Facsimile:+86-755-83768890
Electronic mail: frankwu@topscom.com.cn
Phone :+86 13502814037
Address: #18, Tannan Rd,Tanjia Industrial Region,Gongming Street,Shenzhen City, Guangdong China.

Hong Kong Workplace:

Address : 1st Building Weigan Center JiuLong Hong Kong
Electronic mail: ivy.ko@topscom.com.cn( Ms.Ivy Ko)

2-pcb-house-factory

EasyEDA Zero Cost Net Based EDA Program

EasyEDA is Enthusiastic About New Technology

We’re makers, hackers and technicians. When we wanted to design and develop a few hardware 3 years ago, we invested in 2 or 3 weeks seeking the correct specialized tools. We needed schematic capture, spice simulation and PCB layout nonetheless we needed it to not be solely for Microsoft windows and we didn’t enjoy the idea of needing to pay back hundreds of dollar to get hold of a significant software suite and thereafter commit several weeks learning how to work with it.

Our vision is to help designers move on from theory to constructed prototype more rapidly by serving up broad info and synergy specialized tools for electronic design. Whether you are a novice desperate to explore your very first project or a professional expert seeking a work flow boost, our intention is to take away the tedium in bringing a innovation to reality. We likes to hear what you are focusing on or any thoughts on the way we can help you, hence feel free to email us.

To conclude, EasyEDA will give you a more simple EDA adventure, enabling you to take pleasure in more of the process from a good idea to a item.

Business Line And Prices

There aren’t any totally free business models; EasyEDA has to backup itself and consequently it must always take care of the employees way too.

Endeavouring to offer a disruptive innovation, we provide you with a reliable zero cost internet based EDA program, but yet we make an effort to earn income from several other services, like offering PCB orders, PCB assembly, advertisements and special project reviews by our specialist electronics engineers.

Please apply EasyEDA, we assure EasyEDA’s core features are free of cost to everyone.

Get in Contact with Us

Addr.:

30A, Area A, Shennan Garden Bldg, Nanshan, Shenzhen City, Guangdong
Zip Code: 518000

Business development/partnership:
Dillon@easyeda.com

Other inquiries:
Support@easyeda.com

Conformal Coating Of PCB



Automatic Conformal Coating Of Electronic Assembly. Chemigraphic are an out sourced electronic manufacturing services (EMS) based in Crawley UK.
For more information contact sales@chemigraphic.co.uk

source

Four Suggestions to Selecting a Low-quantity PCB Assembly Fabricator

pwb assy

Working with low-quantity PCB assemblies has its benefits and cons. As the client, there are a few tips that will allow you to get the most from your assembly. In the following paragraphs, we’re going to show you how to benefit from the possible benefits and the ways to get around the negative aspects.

How to Opt for a Low-quantity PCB Assembly Fabricator?

The information pointed out below should help you make the most from your low-quantity PCB assembly order.


1. Single Provider

Go with a low-quantity PCB fabricator who can be a one-stop provider for all of your PCB demands. The great thing about working with a small order is basically you don’t have to coordinate with various organizations or individuals. Your order can be treated by a single point of contact.


2. Value of Prototypes

Even though working with small orders, you must insist on use of prototypes – despite the fact that it comes at an extra cost. Prototypes will assist you to review your design and reinforce it, as you desire.


3. Low-quantity PCB Fabricator

pwb assy

Making low-quantity PCB assemblies can be quite a task when employing an not experienced fabricator. Given that the order quantity is low, expense of production will likely be more or less higher. Hence, any misstep by the PCB fabricator will result in larger losses for the client.


4. Standard PCB Practices

Standard guidelines related to PCB fabrication must be adopted even though working with a low-quantity PCB assembly. This can include design, fabrication, assemblage, and also PCBA testing steps.

Working with a low-quantity PCB assembly has its own group of pros. With standard best practices will assist you to build an order that will help you in time.

Printed Circuit Board Design, Fab & Assembly Services



PNC Specializes in Quick Turn Prototype PC Boards starting at 24 Hour turn times without sacrificing Quality. We have been the Leader of quick turn for 45 Years using the latest Manufacturing processes and equipment.

Our quick turn Prototype PCB service is designed to deliver your most urgent PC boards in as little as 24 hrs. These Printed Circuit Board prototypes will be made with the same quality standards that you are accustomed to with PNC. With our unprecedented record of on-time delivery and quality, rest assured, you will get your product on time to meet your most critical project deadlines.

source

4 Tricks to Choosing a Low-quantity PCB Assembly Maker

pc board assy

Working with small-quantity PCB assemblies has its upsides and cons. As the consumer, there are several hints that will assist you to obtain the most out of your assembly. In the following paragraphs, we will let you know how to utilize the good things and approaches to go around the negative aspects.

Tips on how to Opt for a Low-quantity PCB Assembly Maker?

The guidelines brought up here should help you maximum benefit out of your small-quantity PCB assembly order.


1. Single Supplier

Choose a small-quantity PCB maker who could be a one-stop supplier for all of your PCB demands. The good thing about working with a small order is basically that you don’t need to coordinate with several organizations or individuals. Your order can be treated by a single point of contact.


2. Worth of Prototypes

Although working with small orders, you must insist on using prototypes – despite the fact that it generates an increased cost. Prototypes will help you to inspect your design and improve on it, if necessary.


3. Low-quantity PCB Maker

pc board assy

Fabricating small-quantity PCB assemblies can be a task when cooperating with an unsophisticated maker. Considering that the order quantity is low, cost of production is going to be a little higher. Subsequently, any error on the part of the PCB maker will give rise to larger losses for the client.


4. Standard PCB Practices

Standard tips related to PCB fabricating really should be taken although working with a small-quantity PCB assembly. This consists of design, fabricating, assemblage, and also PCBA testing processes.

Working with a small-quantity PCB assembly has its own group of benefits. With the help of standard recommendations will assist you to build an order that will help you down the road.

Older posts

© 2017 PCB Prototype

Up ↑